DRAIN FROM
ICE MAKER
ICE MAKER
POWER CORD
DRAIN
TRAP
ACCESS PANEL
1-1/2” (3.8 cm) DRAIN PIPE
5/8” (.63 cm) I.D.
DRAIN TUBING
AND HOSE CLAMP
TUBING CLAMPS
VENT TUBE
SUPPLIED SCREWS
DISCHARGE TUBE GOES THROUGH
THIS OPENING IN THE ACCESS PANEL
ACCESS PANEL
DRAIN PUMP
DRAIN PUMP
POWER CORD
DRAIN FROM
ICE MAKER
VENT TUBE GOES THROUGH THIS
OPENING IN THE ACCESS PANEL
DRAIN PUMP’S DISCHARGE LINE
THROUGH THIS OPENING
Front
of Unit
Top of
Unit
6-3/4”
(17.1 cm)
4-1/16”
(10.3 cm)
2-3/8”
(6.0 cm)
14-3/4”
(37.5 cm)
24-5/8” (62.6 cm)
22” (55.9 cm)
15
1
2
3
4
HOW THE ICE MACHINE WORKS
Your ice machine is unique in forming ice. It uses fractional freezing to form a slab of ice that is clear and has less
mineral content than the water it is produced from. This is accomplished by running water over the cold evaporator
plate which gradually freezes the water to produce the ice slab. Mineral deposits are left in the reservoir.
When the ice slab reaches the correct thickness determined by the temperature of the evaporator plate, the electronic
control switches to the harvest cycle to harvest the ice slab. During the harvest cycle, the ice slab falls from the
evaporator to the ice grid cutter. Here, the ice slab is cut into 3/4” squares by the grid cutter’s low voltage heated
wires. During the harvest cycle, the drain valve will remain open for 45 seconds to drain the reservoir of remaining
deposits. After that, the water valve will open for 2 minutes providing 2 quarts of water to the reservoir for the next ice
production cycle.
The ice machine will keep producing ice until the ice machine’s storage bin is full and will restart automatically when ice
needs to be replenished in the storage bin.
To begin ice production, turn the switch to the “ON” position.
Ice Machine Safety and Operation Tips
•Avoid leaning on the cabinet door. You may bend the door hinge or tip the unit.
•Exercise caution when sweeping, vacuuming, or mopping near the front of the unit. Damage to the grill and/or switch
can occur.
•Periodically clean the inside of the ice machine components and inside of the unit.
•Periodically check and/or clean the front grill and condenser coils.
14
DRAIN PLUMBING
Your ice machine uses a gravity drain that requires 5/8” (.63 cm) ID tubing from the back of the ice maker to a plumbed
connection to a sanitary sewer (see Gravity Drain drawing below). Remove the access panel, with a 5/16” (0.8 cm)
wrench to plumb in drain connection. Gravity drain location for built-in units can be within the area shown in illustration
below. An optional drain pump can be purchased for your ice machine if a gravity drain is not accessible. Observe
and follow all local codes when installing an ice machine.
GRAVITY
DRAIN
DRAIN PUMP
Model Number -
VUIM-DP
(
(Sold separately - see
installation instructions
supplied with drain
pump)
GRAVITY DRAIN LOCATION
WARNING
Failure to use adequate drainage system will result in surrounding water damage and/or poor ice production.
ICE MACHINE FEATURES
1. Escutcheon Panel
2. Ice Storage Bin
3. Ice Scoop
4. On/Off/Clean Rocker Switch
(21 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales