Viking K-1900-8 Especificaciones descargar pdf (Pagina 5)

Features

Tenant’s phone numbers: 001-002 (0-32 digits), 003-250 (0-16 digits) ................

Tenant’s phone numbers and keyless entry codes ..............................................

Keyless entry code only (4 - 6 digits) ...................................................................

Master keyless entry code (4 - 6 digits) ................................................................

Maintenance personnel entry codes (4-6 digits) ..................................................

Clear one phone number and/or keyless entry code ............................................

PABX line access number: 1-3 digits + 3 sec pause (factory disabled) ................

Relay activation time: 1/2-99 sec (00 = 1/2 sec, factory set to 5 sec) ...................

Relay activation code*: 1-2 digits (factory set to 36) ............................................

Security code (factory set to 845464) ..................................................................

Maximum call time: 0-99 min (00 = disabled, factory set to 2 min) ......................

To exit remote programming ................................................................................

Normal dialing speed (120ms on/off, factory setting) ...........................................

Fast dialing speed (50ms on/off) ..........................................................................

Apartment dialer mode (factory setting) ...............................................................

Multi-number dialer mode ....................................................................................

Ring thru mode OFF (factory setting) ...................................................................

Ring thru mode ON ..............................................................................................

To add a 4 second pause anywhere in the dialing string ......................................

To add a 1 second pause anywhere in the dialing string ......................................

Enable 911 and 311 calling from entry phone (factory setting) .............................

Disable 911 and 311 calling from entry phone ......................................................

To add a

Q at any point in the dialing string ..........................................................

To add a # at any point in the dialing string ..........................................................

Clear all phone numbers and keyless entry codes from memory

and set all programming features back to factory settings ...................................

phone number

phone number + #Q + entry code +

Q + entry code

#Q + entry code

Q + entry code

(no digits)

1-3 digits

2 digits (00 - 99)

1-2 digits (00 - 99)

6 digits (0 - 9)

2 digits (00 - 99)

(no digits)

###

#001-250

#000

#251-255

#001-255

##2

##3

##4

##5

##6

##7

* Note: When a single digit relay activation code is programmed (0-9), the activation Touch Tone must be held for a minimum of

150 milliseconds.

Notes: “Q”, “#“, pauses occupy one digit space in memory. To clear a memory location, enter “#“ + the memory location without any

preceeding digits. A valid

programming entry will be indicated by a double beep. An invalid entry will be indicated with three beeps.

E. Programming Features Quick Reference

Memory

Location

Enter Digits

- then -

(Caution: Permanently erases ALL programming!)

F. Programmable Maximum Call Time

The K-1900-3 can be programmed to limit the call time on the entry phone. The maximum call time is programmable from “00” (no

maximum call time) to “99” (99 minutes) and is factory set to “02” (2 minutes) (see Programming, section D). When the call timer

is enabled (programmed to “01-99”), if a call exceeds the programmed time, both phones are provided with three beeps then dis-

connected, indicating the termination of the call. This limits unnecessary and lengthy conversations. When the call timer is disabled

(programmed to “00”), there is no limit to the length of calls from the entry phone. Only a CPC disconnect signal from the telephone

line, or hanging up the entry phone will disconnect the call.

G. Built-In Toll Restriction

The K-1900-3 features built-in toll restriction. When the K-1900-3 is in the Apartment Dialer Mode (factory setting), the unit will

disconnect when it detects any Touch Tone or pulse dialing generated by the entry phone, after speed dialing has been completed.

With the K-1900-3 in the Multi-Number Dialer Mode, the unit will disconnect when it detects any flashes or pulse dialing generat-

ed by the phone after speed dialing has been completed.

When a visitor accesses the entry phone, simulated dial tone is heard. After the visitor enters the appropriate one to three digit ten-

ant number (equal to the memory location in programming), the K-1900-3 dials the tenant’s phone number and bridges the phone

line to the entry phone. If an unprogrammed tenant number is entered, a simulated fast busy signal will be heard on the entry phone.

When the tenant confirms the visitors identity, a one or two digit relay activation code may be entered from the tenant’s phone. Two

beeps will indicate that a valid activation code has been entered. A buzzing sound is then heard on the entry phone to indicate the

door strike has been activated. The level of this sound can be controlled independently from other tones by adjusting the Doorstrike

Buzz Volume Control (see Installation section B). If an incorrect relay activation code is entered, the unit will disconnect. A simu-

lated fast busy signal will also be returned to the entry phone if the telephone line has become disconnected. A tenant may use their

personal keyless entry code to let themselves in by taking the entry phone off-hook and entering a “#” followed by their (4 - 6 digit)

personal keyless entry code. Note: To avoid busy signals on the entry phone, call waiting is recommended on each

tenant’s phone line.

A. Apartment Dialer Mode (factory setting)

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

Viking K-1900-8 Especificaciones Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Viking K-1900-8