Viking K-1900-8 Especificaciones descargar pdf (Pagina 4)

You are allowed to program a keyless entry code in a memory location without programming a phone number. This is useful

when you need to assign keyless entry codes for people that are not tenants in the complex (guards, maintenance workers,

etc.) The memory location becomes dedicated to keyless entry storage. This is programmed by entering “#Q” (skipping the

phone number entry) + the keyless entry code (4-6 digits) + “#” + the memory location (001-250). Example: #Q 123456 # 001

3. Programming a Keyless Entry Code Without a Phone Number

While in programming dial a “#” + memory location (000 - 255) to clear. Note: It is not possible to erase only the phone num-

ber or the keyless entry number. If either number needs to be changed, BOTH numbers must be reprogrammed.

6. Deleting the Phone Number and/or Keyless Entry Code for One Memory Location

The master keyless entry code is simply an additional keyless entry code in memory position 000. This is useful when you

have a full 250 tenants and require one additional entry code for a non-tenant (guard, maintenance worker, etc.) This is pro-

grammed by entering “#Q” (skipping the phone number entry) + the keyless entry code (4 - 6 digits) + “#” + the memory loca-

tion 000. Example: #Q 123456 # 000

4. Adding a Master Keyless Entry Code

While in programming, enter “###”. This will clear all phone numbers, entry codes and set all programming back to the facto-

ry settings. CAUTION: All phone numbers and keyless entry codes will be permanently erased.

7. Deleting All Phone Numbers and Keyless Entry Codes

C. Tenant’s Phone Numbers and Keyless Entry Codes

The K-1900-3 can be programmed with up to 250 tenant phone numbers and up to 250 keyless entry codes, a master keyless entry

code, and 5 maintenance entry codes. A tenant may activate the door strike from the entry phone by dialing a “#” followed by their

keyless entry code. When a given tenant moves out of the complex, the phone number and keyless entry code for that tenant may

be cleared without affecting any other tenant’s phone numbers or their keyless entry codes. Likewise, maintenance keyless entry

codes may be assigned temporarily and cleared when no longer needed. Note: A keyless entry code may be programmed without

a phone number.

Note: Keyless entry codes MUST be programmed while programming the phone numbers into the memory locations (001 -

250). While in programming, enter the tenant’s phone number + “#Q” + the keyless entry code for the tenant (4-6 digits) + “#”

+ memory location number (001 - 250). Example: 5551212 #Q 123456 # 001

2. Programming a Phone Number and Keyless Entry Code

While in programming, enter the tenant’s phone number + “#” + memory location number (001 - 250).

Example: 5551212 # 001

1. Programming a Phone Number Only

Five maintenance personnel keyless entry codes are available, occupying memory positions 251 - 255. This is useful when you

require additional entry codes for a non-tenant (guard, maintenance worker, etc.) These would ordinarily be assigned tem-

porarily and then cleared when no longer needed (see number 6 below). This is programmed by entering “#Q” + the keyless

entry code (4 - 6 digits) + “#” + the memory location (251 - 255). Example: #Q 123456 # 251

5. Adding a Maintenance Personnel Keyless Entry Code

D. Programming Examples

These examples would be entered after accessing programming as shown in section A.

Programming the K-1900-3...

1. ...to dial 555-1234 when a “1” is entered at the entrance phone

2. ...to dial a 9 and pause 3 seconds prior to dialing all numbers

3. ...to activate the door strike/magnetic lock when the tenant dials a “66”

4. ...to set keyless entry code for tenant 3 to “9876” with phone number 555-1234

5. ...to set a keyless entry code for tenant 4 to “9876” without a phone number

6. ...to delete the keyless entry code and phone number for tenant 5

7. ...to set a maximum call time of 10 minutes

8. ...to set the master keyless entry code to “123456”

Enter Digits

5551234 #001

9 ##2

66 ##4

5551234#

Q9876 #003

Q9876 #004

#005

10 ##6

#Q123456 #000

B. Security Code

A six digit number may be used to access the programming mode. The security code has been factory set to 845464 (V-I-K-I-N-G).

It is recommended that you change the security code to a personal 6 digit number as follows:

1. Access programming as shown in section A.

2. Enter your new security code followed by ##5.

3. To exit remote programming, enter ##7 or do not enter any touch tones for at least 20 seconds. To exit local

programming simply hang up the entry phone.

Note: The security code must be six digits in length and MUST NOT contain a

or #. If you have forgotten your security code, see

section “A. Local Programming Without the Security Code.”

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

Viking K-1900-8 Especificaciones Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Viking K-1900-8