8.
The 1600A series phone is factory set to automatically start playing the
voice announcement after it has determined the call has been answered.
Alternately, the announcement may be programmed to play after a pro-
grammed amount of time, from 1 to 99 seconds after dialing.
* Note: If the announcement delay time is used, you must allow enough time for the 1600A series phone to detect
ring-no-answer and busy signals when using the redial features. The factory default is set to play automatically.
Settings A and B - Announcement Delay
Touch Tone
00
01-99
Setting A/B
Play automatically
1-99 seconds*
G. Voice Announcer Options (memory location #17)
The 1600A series phones have a built-in non-volatile digital voice announcer that may be used to identify the location
of the emergency phone call. The 16 seconds of digital record time is recorded remotely from a Touch Tone phone.
Programming options are as follows:
Dial: A +B+C+D+E+F+#+1+7
Factory Default Setting:0+0 +0+0+ 0+0
Two Digit Announcement Delay {
Repeat Announcement Setting
Future Use (enter “0”)
Enter Settings Here:
A B C D E F
0 0 0 #17
If enabled and a busy is detected, the 1600A series phone will dial the next pro-
grammed speed dial number, and continue to cycle through the emergency num-
bers until a call is completed. * Notes: This feature is disabled in the factory
default setting. If the busy signal is interrupted with a promotional message, con-
tact your central office to have it removed.
Setting E - Dial Next Number on Busy
Setting F - Pulse Dialing Rate (Pulses per second)
The 1600A series phone is capable of different pulse dialing speeds.
* Note: The factory default setting is 10pps.
Touch Tone
1
2
Setting F
10 pps*
20 pps
Touch Tone
1
2
Setting E
Disabled*
Enabled
Setting C - Silence Time Out
This feature selects the length of time that calls will remain connected without voice activ-
ity. Programmable in increments of 10 seconds up to a maximum of 90 seconds (Touch
Tones 1 - 9). To disable the silence time out, program 0 in this location. Use chart at the
far right. * Note: The factory default is 40 seconds.
Setting D - Dial Next Number on Ring No Answer
If enabled and a ring-no-answer is detected, the 1600A series
phone will dial the next programmed speed dial number, and con-
tinue to cycle through the emergency numbers until a call is com-
pleted. * Note: This feature is disabled in the factory default setting.
Touch Tone
1 or 0
2, 3, 4...9
Setting D
Disabled*
Dials second number after
2, 3, 4...9 rings respectively
Setting B - Call Length Time Out
This feature selects the maximum length of time that calls can be connected.
Programmable in increments of 1 minute up to a maximum of 9 minutes (Touch Tones 1 -
9). Program 0 in this location to disable the call length time out. With the call length dis-
abled, the 1600A series phone must rely on a CPC signal, busy signal, silence or return to
dial tone to hang-up. Use chart at the right. * Note: The factory default is 3 minutes.
Touch
Tone
0
1
2
3
4
5
6
7
8
9
Silence
Time Out
Disabled
10 sec
20 sec
30 sec
40 sec*
50 sec
60 sec
70 sec
80 sec
90 sec
Touch
Tone
0
1
2
3
4
5
6
7
8
9
Call Length
Time Out
Disabled
1 min
2 min
3 min*
4 min
5 min
6 min
7 min
8 min
9 min
(8 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales