The SRC-1 can be programmed with up to 32 keyless entry codes. This feature allows a user to activate the relay by entering a
pre-programmed code on the entry phone keypad. Each keyless entry code can contain 1-6 digits (0-9 or Q) and is programmed
by entering the digits to any of the locations #00 - #31. To clear a location, enter # + the position number without any
preceding numbers.
This six digit number is used to access the programming mode. It is factory set to 845464 (V-I-K-I-N-G). It is recommended that you
change the security code to a personal 6 digit number. To change the security code, access programming (see Programming sec-
tion A). Enter six digits 0-9 followed by #47. If you have forgotten your security code, follow the steps in Programming section A,
3. Programming without the Security Code.
B. Security Code
3
B. Line Powered Entry Phone to CO Line or Analog PABX/KSU Station (Talk Battery Provided by Line In)
OR
*** CO Line or Analog
PABX/KSU Station
OR
OR
OR
OR
E-10A (not included) E-20B (not included)
E-40-PB
(not included)
E-50-SS
(not included)
E-30 (not included) E-35 (not included)
** K-1700-3 (not included) ** K-1705-3 (not included)
* K-1900-5
(not included)
Doorstrike
Power Supply
12-24V AC or DC
Doorstrike
Door
12V DC Adapter
(included)
OR
Power Input
Polarity
Share power with 12-24V
C/DC doorstrike with 200mA
available current or use the
included 12V DC adapter.
T
P
G
LED 1
C
1
8
LED 2
C
VIKING
©
VIKING
ELECTRONICS
HUDSON,
WI
54016
SECURE TOUCH TONE
RELAY CONTROLLER
POWER 12V DC
MODEL SRC-1
ON OFF
LINE IN
1234 789
ENTRY
DEVICE
56
TRIGGER
INPUT
PWR
TALK
BATTERY
N.C.
COM
N.O.
Postal Lock /
Request to
Exit Contact
* Note: The K-1900-5 Dialer is not required if installed on a ringdown circuit. The K-1900-5’s
touch tone and flash restrictions must be disabled (
Q
02).
** Note: K-1700-3, K-1705-3 or other touch tone phone required for keyless entry feature.
*** Note: Set unit to
Q
1 or
Q
5 mode (timed/unlimited dialing) unless installed on a ringdown
circuit. Enable keyless entry/ringdown hang-up (
Q
3) when installed on a ringdown circuit.
TPG
LED 1
C
1
8
LED 2
C
VIKING
©
VIKING
ELECTRONICS
HUDSON,
WI
54016
SECURE TOUCH TONE
RELAY CONTROLLER
POWER 12V DC
MODEL SRC-1
ON OFF
LINE IN
1234 789
ENTRY
DEVICE
56
TRIGGER
INPUT
PWR
TALK
BATTERY
N.C.
COM
N.O.
JP1
JP1
Normal
Position
4
3
2
1
"Learn"
Position
A. Entering the Programming Mode
1. Programming with Line Powered Entry Phone Connected (Talk Battery OFF)
Step 1. Call into the C.O. line or PABX extension connected to ‘Line In’ of the unit.
Step 2. Come off-hook with the entry phone (all Viking handsfree phones can auto answer).
Step 3. Enter
Q and the Security Code (factory 845464) from the ‘Line In’ phone.
Step 4. Two beeps should be heard, you are now in the programming mode.
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
Note: All programming must be performed from the secure (LINE IN) side of the SRC-1.
2. Programming with Adapter-Powered Doorbox Connected (Talk Battery ON)
Step 1. Go off-hook or ring from the doorbox, or go off-hook with the ‘Line In’ phone.
Step 2. Come off-hook with the ‘Line In’ phone, or answer with the doorbox.
Step 3. Enter Q and the Security Code (factory 845464) from the ‘Line In’ phone.
Step 4. Two beeps should be heard, you are now in the programming mode.
3. Programming without the Security Code
Step 1. Move JP1 jumper onto pins 1 & 2, as shown in
the diagram right.
Step 2. Follow steps 1 and 2 from the appropriate
procedure above.
Step 3. Two beeps will be heard on the ‘Line In’ phone,
you are now in the programming mode.
Step 4. After programming, move JP1 jumper back
to pins 3 & 4.
Note: To program a product wired to ENTRY DEVICE, remove power from the SRC-1. This prevents the SRC-1 from reacting to touch
tones and connects LINE IN to ENTRY DEVICE.
C. Keyless Entry Codes
(11 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales