Viking F20465A Manual de usuario descargar pdf (Pagina 16)

3130

SSeeaalleedd SSuurrffaaccee BBuurrnneerrss ((IIff aapppplliiccaabbllee))

Wipe up spill-overs as soon as possible after they occur and before

they get a chance to burn in and cook solid. In the event of a spill-

over, follow these steps:

1. Allow the burner and grate to cool to a safe temperature level.

2. Lift off the burner grates.

3. Remove the burner cap and clean per instructions below.

4. Wipe up any spills which remains on the sealed top surface.

5. Wash grates and burner caps in hot, soapy water and rinse clean.

6. Replace burner cop and grate after drying thoroughly.

If ports on the open or sealed burners are clogged, clean with a

straight pin. Do not enlarge or distort the ports. Do not use a

toothpick to clean the ports. When replacing burner caps, carefully

align the tabs underneath the cap with the outside edge of burner.

Make sure the tabs are not aligned with the igniter and the burner cap

is level.

SSeeaalleedd BBuurrnneerr AAlluummiinnuumm BBaassee ((IIff aapppplliiccaabbllee))

The aluminum base should be wiped regularly withhot soapy water at

the end of each cooling period.

DDOO NNOOTT

use steel wool, abrasive

cloths, cleanser, or powders. To remove encrusted materials, soak the

area with a hot towel to loosen the material, then use a wooden nylon

spatula.

DDOO NNOOTT

use a metal knife, spatula, or any other metal tool to

scrape the aluminum base.

NNOOTTEE

: For stubborn stains, use a non

abrasive cleanser such as Bon Ami

and a soft brush or soft Scoth

Brite

pad.

BBuurrnneerr CCaappss

The surface burner caps should be routinely removed and cleaned.

Always clean the burner caps after a spill over. Keeping the burner

caps clean will prevent improper ignition and uneven flames. To clean,

pull burner cap straight up from the burner base. Wipe off surface

burner caps with warm, soapy water and a soft cloth after each use.

Use a a non-abrasive cleanser such as Bon Ami and a soft brush or soft

scotch brite

pad for cooked-on foods. Dry thoroughly after cleaning.

For best cleaning and to avoid possible rusting, do not clean in

dishwasher or self-cleaning oven.

CCoonnttrrooll KKnnoobbss

MAKE SURE THE CONTROL KNOBS POINT TO THE OFF POSITION

BEFORE REMOVING. Pull the knobs straight off. Wash in detergent

and warm water. Do not soak knobs. Dry completely and replace by

pushing firmly onto stem. DO NOT USE any cleaners containing

ammonia or abrasives. They could remove the graphics from the knob.

CCoonnttrrooll PPaanneell

DDOO NNOOTT UUSSEE aannyy cclleeaanneerrss ccoonnttaaiinniinngg aammmmoonniiaa oorr aabbrraassiivveess

. They

could remove the graphics from the control panel. Use hot, soapy

water and a soft clean cloth.

WWookk CCaasstt IIrroonn BBuurrnneerr ((IIff aapppplliiccaabbllee))

For proper lighting and performance of the burner, keep the

electric igniter and burner ports clean. It is necessary to clean these only

when the flame does not burn blue completely around all rings of the

burner, when there is a severe spillover or when the burner does not

light, even though the electric spark igniter sparks. Clean the burner by

scraping off burned on food soil. Use a wire, a straightened paper clip,

or needle to clean the ports.

DDoo nnoott uussee aa ttooootthhppiicckk;; iitt ccoouulldd bbrreeaakk ooffff

iinn tthhee ppoorrtt.. BBee ssuurree tthhee vveennttuurrii ttuubbee rreemmaaiinnss ddrryy..

Burner

ports

Venturi tube

1 2 ... 11 12 13 14 15 16 17 18 19 20

Comentarios a estos manuales

Sin comentarios

Viking F20465A Manual de usuario Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Viking F20465A