Viking FDRB5302L Manual de instalación

Viking Range, LLC111 Front StreetGreenwood, Mississippi 38930 USA(662) 455-1200For product information,call 1-888-(845-4641)or visit the Viking Web si

79-3/8”(201.6 cm) min.to bottom of anti-tip board80-1/2”(204.6 cm) max.to bottom of anti-tip boardOne 2”x 4” mounting board per unit1-1/2” (3.8 cm) x

79-3/8”(201.6 cm) min.to bottom of anti-tip board80-1/2”(204.6 cm) max.to bottom of anti-tip boardOne 2”x 4” mounting board per unit1-1/2” (3.8 cm) x

1/2”(1.27 cm)1-1/2”(3.81 cm)1/4” Radius(.64 cm)2-3/4”(6.98 cm)1/2”(1.27 cm)3/4”(1.90 cm)1/2”(1.27 cm)1/8”(.31 cm)1/2”(1.27 cm)1/4” Radius1/4” Radius(1

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds

Top ViewFlush mount cabinet doors24”(61.0 cm)standard cabinetdepth24”(61.0 cm)standard cabinetdepth24”(61.0 cm)standard cabinetdepth24-3/4”(62.9 cm)Ca

3/4”(1.9 cm)End panel1”(2.5 cm)1/4”(0.6 cm)Z-Bracket21-3/4”(55.2 cm)21-3/4”(55.2 cm)24”(61.0 cm)Optional kickplate notch(Dimensions determined by cabi

5132Remove handle side cabinet screws and trim with a phillips screwdriver.Remove all screws from handle side door trim. Remove two screws from top an

353412Remove air grille center blade.Remove two 1/4” (0.6 cm) screws with a magneticextended screwdriver at least 8” (20.3 cm) long.34Pull air grille

3637General InformationArea RequirementsVerify the following:• Unit can fit into residence and can be movedaround corners and through doorways.• Floor

32Table of ContentsWarnings & Important Information ____________________________________________________________________3All Refrigerator/FreezerD

3938General Information• Most of the unit’s weight is at the top. Extracare is needed when moving the unit to prevent tipping. • DO NOT remove protect

4140Replace unit top and four side screws.Attach one 2 x 4 to wall stud (refer to dimensions pagefor exact location).If needed, depending on cabinet a

4342Verify that drain pan is installed and aligned.Align holes on both ends of louvered panels and insert screws.Using a phillips screwdriver, attach

4544Performance Checklist□ Verify cabinet size.□ Verify electrical supply and water supply (if applicable).□ Install anti-tip device(s) and verify uni

4746Only authorized replacement parts may be usedin performing service on the appliance. DO NOTrepair or replace any part of the appliance unlessspeci

5IMPORTANT–Please Read and Follow!4A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, orlocal ordinances.•

35”(88.9 cm) 23-13/16”(60.4 cm)24-3/4”(62.9 cm)82-7/8”(210.5 cm)min.to84-15/16”(213.5 cm)max.82-7/8”(210.5 cm)min.to84-1/16”(213.5 cm)max.75-15/16”(19

One 2”x 4” mounting board1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards b

One 2”x 4” mounting board1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting boards b

75-15/16”(192.9 cm)3-1/2”(8.9 cm)30”(76.2 cm)29”(73.7 cm)29-1/2”(74.9 cm)1”(2.54 cm)between units35”(88.9 cm)82-7/8”(210.5 cm)min.to84-15/16”(213.5 cm

Specifications 75-15/16”(192.9 cm)3-1/2”(8.9 cm)1”(2.54 cm)between units35”(88.9 cm)82-7/8”(210.5 cm)min.to84-15/16”(213.5 cm)max.36”(91.5 cm)Measurem

79-3/8”(201.6 cm) min.to bottom of anti-tip board80-1/2”(204.6 cm) max.to bottom of anti-tip boardOne 2”x 4” mounting board per unit1-1/2” (3.8 cm) x